Sea-Doo Sportster 4-TEC Fresno CA

The Sea-Doo Sportster 4-TEC is a speedy 15-ft. runabout with a propulsion package that offers excellent maneuverability and an added measure of swimmer safety that can't be matched by any propeller-driven boat. The Sportster 4-TEC is rated to carry 4 passengers or 715 lbs. total passengers and gear.

A 1 Boat & Jet Ski
(559) 323-9016
2901 E Alluvial Ave
Clovis, CA
Services
A 1 Boat & Jet Ski

Data Provided by:
Hypercycles Of Fresno
(559) 233-1290
1505 N Blackstone Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Action Auto Towing
(559) 498-9999
2822 East California Avenue
Fresno, CA
 
Clawson Motorsports
(559) 435-5020
6334 North Blackstone Avenue
Fresno, CA
 
Bohner Boat & Marine
(559) 431-0336
10740 W North Ave # 41
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

CMS Toys LLC
(559) 255-6592
5290 Millerton Rd
Friant, CA
Services
CMS Toys LLC

Data Provided by:
Belmont Marine
(559) 237-2597
2006 W Belmont Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Local Photo ADS
(559) 225-2704
1610 East Gettysburg Avenue
Fresno, CA
 
Ron'S Marine
(559) 292-6370
2782 N Sunnyside Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

American Recreational Marine
(559) 253-7470
4974 E Clinton Way
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Data Provided by:

Sea-Doo Sportster 4-TEC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sea-Doo Sportster 4-TEC is a speedy 15-ft. runabout with a propulsion package that offers excellent maneuverability and an added measure of swimmer safety that can't be matched by any propeller-driven boat. The Sportster 4-TEC is rated to carry 4 passengers or 715 lbs. total passengers and gear.

Construction
After the gelcoat is applied to the mold, the builder uses a premium vinylester resin to wet out the first layer of fiberglass chop in the hull, providing excellent resistance to osmotic blistering. A core of end-grain balsa follows for added stiffness at moderate weight, then a second layer of chop and wet out with general purpose orthophthalic resin is applied on top of the balsa to complete the hull's structural sandwich. Fiberglass-woven roving reinforcements are used along the spray strakes in the hull bottom. Usually reinforcements are used throughout the hull laminate, but BRP, the manufacturer, reports having no trouble with this method. A pair of foam stringers follows, bonded to the hull and then encapsulated in more chop. The cockpit deck liner is similarly constructed, but with a foam core in the deck for stiffness, and this structure is bonded to hull stingers. The transom is solid fiberglass, about 1/2 in. thick.

The hull-to-deck joint is bonded with Sikaflex, a death-grip adhesive stronger than the fiberglass itself, and fastened in place with aluminum pop rivets that basically serve to hold the joint clamped until the Sikaflex sets up. More pop rivets hold the rubrail in place to the gunwale. The fuel tank can be replaced, if need be, by first removing the engine. This eliminates having to cut a hole in the deck, which is the case with many other boats in this size range. In any event, it is unlikely that the tank would ever need to be replaced, as crosslink polyethylene cannot rot. ...

Click here to read the rest of the article at JDPower.com