Scout 190 Costa Flats Clovis CA

The Scout 190 Costa Flats is a pure flats boat, with a retractable casting platform in the bow (a little extra height helps put to the lure out further) and a second, higher casting platform in the stern. It has a capacity of 6 (or 1,100 lbs. of) passengers, a 2,000 lb. total capacity, and a maximum rating of 225 hp.

A 1 Boat & Jet Ski
(559) 323-9016
2901 E Alluvial Ave
Clovis, CA
Services
A 1 Boat & Jet Ski

Data Provided by:
Pine Flat Lake Marina
(559) 787-2506
P.O. Box 345
Piedra, CA
Services
Houseboat Rentals

Data Provided by:
A Wet & Wild Motorsports
(559) 299-3165
1129 Railroad Avenue
Clovis, CA
 
Grove Boat Lift
(559) 251-5115
Po Box 8095
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Clovis Marine
(559) 291-5737
2475 N Fordham Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

CMS Toys LLC
(559) 255-6592
5290 Millerton Rd
Friant, CA
Services
CMS Toys LLC

Data Provided by:
Fiberglass Unlimited
(559) 299-8826
1025 San Jose Avenue
Clovis, CA
 
N & N Boats
(559) 322-9736
1631 Tollhouse Road
Clovis, CA
 
Ron'S Marine
(559) 292-6370
2782 N Sunnyside Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Clawson Motorsports
(559) 435-5020
6334 North Blackstone Avenue
Fresno, CA
 
Data Provided by:

Scout 190 Costa Flats

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Scout 190 Costa Flats is a pure flats boat, with a retractable casting platform in the bow (a little extra height helps put to the lure out further) and a second, higher casting platform in the stern. It has a capacity of 6 (or 1,100 lbs. of) passengers, a 2,000 lb. total capacity, and a maximum rating of 225 hp.

ConstructionScouts are very well built, as well as any seen in the saltwater fishing industry. They are built entirely of rot-proof fiberglass and composite coring materials""no balsa or any other kind of wood is used structurally. Each Scout starts off with a 3 oz. skin coat of mat wet out in general purpose resin over the gelcoat, followed by fiberglass reinforcements. Many manufacturers use a premium vinylester resin for the skin coat, since it is inherently more resistant to osmotic blistering, but Scout says they have never had a problem with blistering, being very careful to completely wet out the mat with properly catalyzed resin. The vinylester route is preferred, but many take Scout's word for it that blistering has never been a problem, which is what's important in the final analysis.

Divinycell coring is used to stiffen the hull sides, while the bottom is solid fiberglass. A one-piece flanged fiberglass hull support grid is bonded to the hull skin with methacrylate adhesive. One unique characteristic of Scout's design is that the hull stringers continue past the transom to the outboard bracket, so the main hull structure directly absorbs the engine's weight, torque and thrust. Another unique design feature is the hull-to-deck joint, which is a sort of reverse shoe-box joint""the deck fits inside the hull part, and the joint is continuously bonded together using methacrylate adhesive.

Click here to read the rest of the article at JDPower.com