Sailfish 30-06 CC Porterville CA

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Success Marina
(559) 781-2078
30300 Highway 190
Porterville, CA
Services
Success Marina

Data Provided by:
Central Valley Mastercraft
(800) 993-7278
Call, eMail or visit the website
Tulare, CA
 
Packers Bay Marina
(530) 275-5570
4240 Main St
Shasta Lake, CA
Services
Packers Bay Marina

Data Provided by:
Resort Watersports
(858) 488-2582
3981 Mission Blvd
San Diego, CA
Services
Resort Watersports

Data Provided by:
North Pole
(909) 866-7622
618 Pine Knot Ave # A
Big Bear Lake, CA
Services
North Pole Fudge Co?Address:

Data Provided by:
The Boat Shop
(559) 781-3000
30311 Avenue 160
Porterville, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Copco Lake Store
(530) 459-3655
27734 Copco Rd
Montague, CA
Services
Copco Lake Store

Data Provided by:
Pine Flat Lake Marina
(559) 787-2506
P.O. Box 345
Piedra, CA
Services
Houseboat Rentals

Data Provided by:
Golden Gate Saloon
(530) 273-1353
212 W Main St
Grass Valley, CA
Services
Golden Gate Saloon

Data Provided by:
Marina Sailing
(310) 822-6617
4633 Admiralty Way
Marina Del Rey, CA
Services
Marina Sailing

Data Provided by:
Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com