Sailfish 30-06 CC Los Banos CA

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Alamar Restaurant & Marina
(916) 922-0200
5999 Garden Hwy
Sacramento, CA
Services
Alamar Restaurant & Marina

Data Provided by:
Lakeshore Pacific Boat & PWC Rentals: Prompt Court
(916) 771-8800
1101 Tinker Rd
Rocklin, CA
Services
Lakeshore Pacific Boat & PWC Rentals: Prompt Courteous Service

Data Provided by:
Shelter Island Sailing
(619) 222-0351
2240 Shelter Island Dr
San Diego, CA
Services
Shelter Island Sailing

Data Provided by:
St Francis Yacht Club
(415) 563-6363
700 Marina Blvd
San Francisco, CA
Services
St Francis Yacht Club

Data Provided by:
Carlsbad Inn Beach Resort
(800) 235-3939
3075 Carlsbad Blvd
Carlsbad, CA
Services
Carlsbad Inn Beach Resort

Data Provided by:
Pine Flat Lake Marina
(559) 787-2506
P.O. Box 345
Piedra, CA
Services
Houseboat Rentals

Data Provided by:
Lake Oroville Marina LLC
(530) 877-2414
3428 Pentz Rd
Paradise, CA
Services
Lake Oroville Marina LLC

Data Provided by:
Hornblower Cruises & Events
(310) 301-6000
13755 Fiji Way
Marina Del Rey, CA
Services
Hornblower Cruises & Events

Data Provided by:
Estrellita Marina
(530) 286-2215
Trinity Center, CA
Services
Estrellita Marina

Data Provided by:
La Quinta Inn-Redding
(530) 221-8200
2180 Hilltop Dr
Redding, CA
Services
La Quinta Inn-Redding

Data Provided by:
Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com