Sailfish 30-06 CC Fresno CA

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

A 1 Boat & Jet Ski
(559) 323-9016
2901 E Alluvial Ave
Clovis, CA
Services
A 1 Boat & Jet Ski

Data Provided by:
Belmont Marine
(559) 237-2597
2006 W Belmont Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Local Photo ADS
(559) 225-2704
1610 East Gettysburg Avenue
Fresno, CA
 
Clawson Motorsports
(559) 435-5020
6334 North Blackstone Avenue
Fresno, CA
 
Clovis Marine
(559) 291-5737
2475 N Fordham Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

CMS Toys LLC
(559) 255-6592
5290 Millerton Rd
Friant, CA
Services
CMS Toys LLC

Data Provided by:
Hypercycles Of Fresno
(559) 233-1290
1505 N Blackstone Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Action Auto Towing
(559) 498-9999
2822 East California Avenue
Fresno, CA
 
Fresno Boats
(559) 495-1455
9075 S Fruit Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

All Weather Canvas
(559) 292-9136
2888 N Sunnyside Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com