Sailfish 30-06 CC Coalinga CA

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Bass Lake Boat Rentals
(559) 642-3367
N Shore Pines Vlg
Bass Lake, CA
Services
Bass Lake Boat Rentals

Data Provided by:
A 1 Boat & Jet Ski
(559) 323-9016
2901 E Alluvial Ave
Clovis, CA
Services
A 1 Boat & Jet Ski

Data Provided by:
Golden Gate Saloon
(530) 273-1353
212 W Main St
Grass Valley, CA
Services
Golden Gate Saloon

Data Provided by:
A Wet Pleasure Boat & Jet Ski
(707) 966-4204
5800 Knoxville Rd
Napa, CA
Services
A Wet Pleasure Boat & Jet Ski

Data Provided by:
North Pole
(909) 866-7622
618 Pine Knot Ave # A
Big Bear Lake, CA
Services
North Pole Fudge Co?Address:

Data Provided by:
Napa Yellow Pages
(707) 265-7913
Napa, CA
Services
Napa Yellow Pages

Data Provided by:
Big Bear Solar Observatory
(909) 866-5791
40386 North Shore Ln
Big Bear City, CA
Services
Big Bear Solar Observatory

Data Provided by:
Orca Yacht Charters Inc
(949) 650-6722
2901 W Coast Hwy # 170
Newport Beach, CA
Services
Orca Yacht Charters Inc

Data Provided by:
Silverthorn Resort-Marina
(530) 275-1571
16250 Silverthorn Rd
Redding, CA
Services
Silverthorn Resort-Marina

Data Provided by:
Westrec Marina Management Inc
(818) 907-0400
16633 Ventura Blvd
Encino, CA
Services
Westrec Marina Management Inc

Data Provided by:
Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com