Sailfish 30-06 CC Clovis CA

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

A 1 Boat & Jet Ski
(559) 323-9016
2901 E Alluvial Ave
Clovis, CA
Services
A 1 Boat & Jet Ski

Data Provided by:
Pine Flat Lake Marina
(559) 787-2506
P.O. Box 345
Piedra, CA
Services
Houseboat Rentals

Data Provided by:
A Wet & Wild Motorsports
(559) 299-3165
1129 Railroad Avenue
Clovis, CA
 
Grove Boat Lift
(559) 251-5115
Po Box 8095
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

American Recreational Marine
(559) 253-7470
4974 E Clinton Way
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

CMS Toys LLC
(559) 255-6592
5290 Millerton Rd
Friant, CA
Services
CMS Toys LLC

Data Provided by:
Fiberglass Unlimited
(559) 299-8826
1025 San Jose Avenue
Clovis, CA
 
N & N Boats
(559) 322-9736
1631 Tollhouse Road
Clovis, CA
 
Ron'S Marine
(559) 292-6370
2782 N. Sunnyside
Fresno, CA
 
Ron'S Marine
(559) 292-6370
2782 N Sunnyside Ave
Fresno, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Data Provided by:

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com