Sailfish 30-06 CC Chowchilla CA

The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

R J Sales
(559) 674-2142
6306 Road 26 1/2
Madera, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Canvas West
(559) 447-9935
10204 Highway 41
Madera, CA
Services
Parts, Aftermarket Accessories, Supplies, Storage

Rays Small Engine & Marine
(559) 661-4480
500 N E St
Madera, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Canvas Shop
(559) 439-6660
10724 Highway 41
Madera, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Bohner Boat & Marine Inc
(559) 431-0336
10740 Highway 41
Madera, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Pacific Marine Center
(559) 432-2277
10452 N. Hwy. 41
Madera, CA
 
Semper Speed & Marine
(559) 436-1888
10816 Highway 41 # C
Madera, CA
Services
Parts, Service, Aftermarket Accessories, Trailers, Supplies, Storage

Semper Speed & Marine
(559) 436-1888
10854 North Highway 41
Madera, CA
 
Central Valley Auto Sales
(559) 822-2200
41453 Avenue 14 1/2
Madera, CA
 
Bohner Lacefield Marine
(559) 431-0336
10740 Hwy 41
Madera, CA
Services
New Boat Sales, Used Boat Sales, Engine Repair, Boat Storage
Hours
M-F 830am-530pm; Sat 820am-330pm Sunday - closed

Sailfish 30-06 CC

Provided by:

Click here for more content from JDPower.com

Model Introduction
The Sailfish 30-06 Center Console is the largest model in the builder's lineup. It has a clear mission"offshore fishing. Not that it isn't also for other activities as well, such as diving and day cruising, but this boat is designed to head well offshore for fishing, and do so in comfort.

Construction
The skin coat of chop in DCPD resin goes down over the gelcoat, followed by a solid hull laminate of knit fiberglass in the sides and woven roving in the bottom. The hull is supported by a fiberglass, foam-cored Compsys stringer system, and the bulkheads are also foam-cored. The whole network is encapsulated in fiberglass and bonded to the hull. The transom is built of high-density poured foam-cored transom encapsulated in fiberglass. The hull-to-deck joint is bonded with urethane adhesive and stainless self-tapping screws every foot. The rubrail and the stainless insert follows with two more rows of screws fastening the joint. The one-piece cockpit/liner is bonded to the stringers with urethane putty, becoming an integral part of the boat's structure. The cabin liner is also bonded to the hull and to the cockpit liner where they meet at the aft cabin bulkhead. The Sailfish comes with a 10-year structural warranty that covers the hull against defects.

Hull Design
The Sailfish 30-06 CC has a deep-vee hull form with a sharp, deep entry and 24° of transom deadrise. Reverse running strakes (they turn up rather than down from garboard to chine), similar to the old Sea Craft hulls, run the length of the bottom. Its high freeboard increases seaworthiness, helping to prevent boarding seas, while providing high gunwale coamings inside the cockpit and a relatively high cockpit deck level above the waterline. ...

Click here to read the rest of the article at JDPower.com